All pins connected
Bi-directional
High quality construction
2 metres in length
A 25 line parallel printer cable, suitable for use with printers that require a fully occupied cable for full functionality. The cable is fully moulded and shielded and features long thumb screws for ease of installation.
The 2 port KVM switch allows you to connect to control two computers from a single console (monitor, keyboard and mouse). The device allows you to switch between the two computers at the touch of a button. It can be used on any type of computer which has two PS/2 ports and a VGA graphics port
Internal 32 Bit PCI RAID card
Provides 2 ATA-133 ports
Supports up to 4 IDE devices
2 independent IDE/ATA channels
Support RAID sets (striped, mirrored, and mirrored striped) or single drive configuration
Supports mixed drive manufacturers and capacities in the same RAID set
Supports all hard drive capacities
Supports Ultra and Multiword DMA timing modes
CRC (Cyclical Redundancy Check)
128 Bytes Buffer
Built in 80 pin cable detect circuitry
Supports Bus Master DMA at 133MB/sec PCI burst rate
3.3V operating voltage with 5V tolerant I/O
Windows 98SE/ME/NT 4.0/2000/XP compatible
Package contents: 1 x ATA133 RAID PCI Card, 1 x IDE cable, driver CD, installation guide
2 port mini KVM switch
· Ultimate in KVM convenience
· Hotkey port switching
· Cables attached
· Easy installation, no software required
· Control 2 PCs via 1 keyboard, mouse and monitor
· Ideal for video editing
4 Pin 12v P 4 Extension PC Power Cable ( P4 12V Exten Cable )
· 4pin 12V ATX plug - 4pin ATX jack
· Designed to extend the 4 pin 12V power supply between the mains adaptor and the motherboard
· Uses high quality components
· A vocabulary of 160,000 most commonly used words
· A thesaurus of 270,000 synonyms based on 90,000 most commonly used words
· Searches for words with similar spelling or pronunciation
· Searches for words with unknown characters
· Wordsaver - save and recall desired words
· Puzzle solver
· Euro currency converter
· 8 interesting word games, including Hangman and Anagram solver
· 10 digit calculator
· Key tone
· Contrast adjustment
· Auto power off when not in use
· Includes battery (1 x lithium CR2032)
3/16 & 1/4 nut drivers
Spare parts tube
Tweezers
Three claw parts retriever/extractor
IC Extractor
Reversible T10/T15 torque driver
1/8 flat screwdriver
#0 phillips screwdriver
Complete with vinyl zipper case A compact 10 piece multi-purpose computer tool kit. Ideal for upgrades and repairs, as well as general adjustments and maintenance.
Spare parts tube
Tweezers
Three claw parts retriever/extractor
Reverse action tweezers
IC inserter (14-16 pin ICs)
IC extractor
5 needle nose pliers with cutting edge
6 adjustable wrench
8 wire cutter
1/4 flat screwdriver
# 2 phillips screwdriver
3/16 flat screwdriver
#1 phillips screwdriver
1/8 flat screwdriver
# 0 phillips screwdriver
Reversible T10/T15 torque driver
3/16 & 1/4 nut drivers
Complete with vinyl zipper case A multi-purpose 18 piece computer servicing tool kit. Ideal for upgrades and repairs, as well as general adjustments and maintenance.
20 to 24pin Power Supply Converter ( 20 to 24pin cnverter )
· Convert your 20 pin ATX power supply to a 24 pin motherboard of any size
· Enables your current 20 pin PSU to be compatible with all the latest 24 pin motherboards
· Allows you to change the position of your PCI card
· Ideal for use with Mini-ITX and other small form factor applications
· Dimentions: 110x39.1x1.6mm
A handy pack of fixings for general domestic use
Supplied in a case with fixings sorted into compartments
Great value for money! Contents:
2 pcs super hangers
5 pcs picture hangers
5 pcs saw tooth hangers
27 pcs 1 inch brass nails
1 pc 6fts hanging wire
6 pcs 10lb cup hooks
12 pcs screw eyes
2 pcs hardwall hangers<B>
A handy pack of fixings for general domestic use
Supplied in a case with fixings sorted into compartments
Great value for money! Contents:
30 screw eyes:
20 pcs size 5/8 of an inch
10 pcs size 1 inch
28 cup hooks:
10 size 1/2 inch
10 size 3/4 inch
5 size 1 inch
3 size 1 1/4 inch
2 safety cup hooks<B>
A kit containing 100 assorted insulated crimp terminals and connectors. Terminals are tin-plated copper with PVC insulation. Types with red sleeves suit cables from 0.4mm2 to 1.0mm2 and those with blue sleeves from 1.1mm2 to 2.6mm2.
A handy pack of fixings for general domestic use
Supplied in a case with fixings sorted into compartments
Great value for money! Contents:
65 machine screws:
15 pcs size M4 x 10
20 pcs size M4 x 20
10 pcs size M4 x 25
10 pcs size M5 x 12
10 pcs size M5 x 25
60 round head bolts:
40 pcs size M4
20 pcs size M5<B>
A handy pack of fixings for general domestic use
Supplied in a case with fixings sorted into compartments
Great value for money! Contents:
10 pcs wall plugs
10 pcs wall screws
5 pcs cup hooks
30 pcs screw eyes
10 pcs picture hooks
10 pcs nails
40 pcs drawing pins
35 pcs large nails
240 Piece Nut and Bolt Set ( 240pc Nut + Bolt Set )
Contains 19 popular sizes Size Quantity
M4 x 12mm 10
M4 x 20mm 10
M5 x 16mm 10
M5 x 25mm 10
M6 x 20mm 10
M6 x 30mm 10
M8 x 25mm 5
M8 x 40mm 5
M10 x 40mm 5
M10 x 16mm 5
M4 Nut 20
M5 Nut 20
M6 Nut 20
M8 Nut 10
M10 10
Washer Dia 4 20
Washer Dia 5 20
Washer Dia 6 20
Washer Dia 8 10
Washer Dia 10 10
300 Piece Crimp Connector Set ( 300pce Crimp Con Kit )
A kit containing 100 assorted insulated crimp terminals and connectors. Terminals are tin-plated copper with PVC insulation. Types with red sleeves suit cables from 0.4mm2 to 1.0mm2, those with blue sleeves from 1.1mm2 to 2.6mm2 and those with yellow sleeves from 2,7mm2 to 6.6mm2.
‘Lucar’ Piggy-Back Connectors ( Piggy-Back Red 10pk )
Crimp terminal receptacle with a blade terminal angled from the front, allowing another receptacle to be piggy-backed onto the connector. Tin-plated brass with vinyl-PVC insulation. The red types are suitable for cable from 0.4 to 1.0mm, the blue 1.1 to 2.6mm and the yellow 2.5 to 6.5mm. Order Type Length
Code (mm)
L26AY Red 23
L27AY Blue 23
L28AY Yellow 23
Supplied in packs of 10.
‘Lucar’ Piggy-Back Connectors ( Piggy-Back Blue 10pk )
Crimp terminal receptacle with a blade terminal angled from the front, allowing another receptacle to be piggy-backed onto the connector. Tin-plated brass with vinyl-PVC insulation. The red types are suitable for cable from 0.4 to 1.0mm, the blue 1.1 to 2.6mm and the yellow 2.5 to 6.5mm. Order Type Length
Code (mm)
L26AY Red 23
L27AY Blue 23
L28AY Yellow 23
Supplied in packs of 10.
Crimp terminal receptacle with a blade terminal angled from the front, allowing another receptacle to be piggy-backed onto the connector. Tin-plated brass with vinyl-PVC insulation. The red types are suitable for cable from 0.4 to 1.0mm, the blue 1.1 to 2.6mm and the yellow 2.5 to 6.5mm. Order Type Length
Code (mm)
L26AY Red 23
L27AY Blue 23
L28AY Yellow 23
Supplied in packs of 10.
0.1" Series Socket Housing ( PCB Ltch Hsng 12-Way )
A series of sockets that will connect to the 0.1 series PCB plugs. To assemble, solder metal PCB terminals to the end of your wires and then insert them into the housing, where they lock in securely. This forms a polarised connector that will connect only one way round on the matching PCB header plug. Housings are available from 2 to 10 ways to match the plugs. The metal PCB terminals are sold separately in strips of 10 (Order Code YW25C).
0.1" Series Socket Housing ( PCB Latch Hsng 2-Way )
A series of sockets that will connect to the 0.1 series PCB plugs. To assemble, solder metal PCB terminals to the end of your wires and then insert them into the housing, where they lock in securely. This forms a polarised connector that will connect only one way round on the matching PCB header plug. Housings are available from 2 to 10 ways to match the plugs. The metal PCB terminals are sold separately in strips of 10 (Order Code YW25C).
0.1" Series Socket Housing ( PCB Latch Hsng 3-Way )
A series of sockets that will connect to the 0.1 series PCB plugs. To assemble, solder metal PCB terminals to the end of your wires and then insert them into the housing, where they lock in securely. This forms a polarised connector that will connect only one way round on the matching PCB header plug. Housings are available from 2 to 10 ways to match the plugs. The metal PCB terminals are sold separately in strips of 10 (Order Code YW25C).
0.1" Series Right-Angled Sockets ( PCB Skt 2-Way )
Housing with printed circuit type tin-plated phosphor bronze terminals pre-assembled with pins at right-angles to the housings for direct PCB mounting. Thus boards with straight 0.1 series plugs may be connected at right- angles and boards with right-angle plugs may be connected end to end. The housing has a clip which holds it against the edge of the PCB. Pin length: 33mm x 1mm dia. holes, which should be drilled 6mm from edge of PCB. Available in 2, 3, 4 and 12-way.
These connectors are intended as a simple and inexpensive method of making cable to printed circuit board connections. The pins are at standard 0.1 (2.54mm) pitch. These header plugs are designed primarily for accepting the matching sockets below allowing cables to be plugged onto circuit boards or circuit boards to be plugged together. The pins protrude 34mm from the base and require 1mm diameter holes for soldering to the PCB. The pins are 7.5mm long above the base and the header features a locking and polarising clip. Both plugs and sockets may be butted up end-to-end to form connectors with any number of ways from 2 upwards. Rated: 25A, 250Vac. Type Length (mm)
2-way 3.5
3-way 7
4-way 9.5
10-way 24.5
0.1" Series Socket Housing ( PCB Latch Hsng 4-Way )
A series of sockets that will connect to the 0.1 series PCB plugs. To assemble, solder metal PCB terminals to the end of your wires and then insert them into the housing, where they lock in securely. This forms a polarised connector that will connect only one way round on the matching PCB header plug. Housings are available from 2 to 10 ways to match the plugs. The metal PCB terminals are sold separately in strips of 10 (Order Code YW25C).
0.1" Series Right-Angled Sockets ( PCB Skt 3-Way )
Housing with printed circuit type tin-plated phosphor bronze terminals pre-assembled with pins at right-angles to the housings for direct PCB mounting. Thus boards with straight 0.1 series plugs may be connected at right- angles and boards with right-angle plugs may be connected end to end. The housing has a clip which holds it against the edge of the PCB. Pin length: 33mm x 1mm dia. holes, which should be drilled 6mm from edge of PCB. Available in 2, 3, 4 and 12-way.
These connectors are intended as a simple and inexpensive method of making cable to printed circuit board connections. The pins are at standard 0.1 (2.54mm) pitch. These header plugs are designed primarily for accepting the matching sockets below allowing cables to be plugged onto circuit boards or circuit boards to be plugged together. The pins protrude 34mm from the base and require 1mm diameter holes for soldering to the PCB. The pins are 7.5mm long above the base and the header features a locking and polarising clip. Both plugs and sockets may be butted up end-to-end to form connectors with any number of ways from 2 upwards. Rated: 25A, 250Vac. Type Length (mm)
2-way 3.5
3-way 7
4-way 9.5
10-way 24.5
These connectors are intended as a simple and inexpensive method of making cable to printed circuit board connections. The pins are at standard 0.1 (2.54mm) pitch. These header plugs are designed primarily for accepting the matching sockets below allowing cables to be plugged onto circuit boards or circuit boards to be plugged together. The pins protrude 34mm from the base and require 1mm diameter holes for soldering to the PCB. The pins are 7.5mm long above the base and the header features a locking and polarising clip. Both plugs and sockets may be butted up end-to-end to form connectors with any number of ways from 2 upwards. Rated: 25A, 250Vac. Type Length (mm)
2-way 3.5
3-way 7
4-way 9.5
10-way 24.5
These connectors are intended as a simple and inexpensive method of making cable to printed circuit board connections. The pins are at standard 0.1 (2.54mm) pitch. These header plugs are designed primarily for accepting the matching sockets below allowing cables to be plugged onto circuit boards or circuit boards to be plugged together. The pins protrude 34mm from the base and require 1mm diameter holes for soldering to the PCB. The pins are 7.5mm long above the base and the header features a locking and polarising clip. Both plugs and sockets may be butted up end-to-end to form connectors with any number of ways from 2 upwards. Rated: 25A, 250Vac. Type Length (mm)
2-way 3.5
3-way 7
4-way 9.5
10-way 24.5
0.1" Series Right-Angled Sockets ( PCB Skt 4-Way )
Housing with printed circuit type tin-plated phosphor bronze terminals pre-assembled with pins at right-angles to the housings for direct PCB mounting. Thus boards with straight 0.1 series plugs may be connected at right- angles and boards with right-angle plugs may be connected end to end. The housing has a clip which holds it against the edge of the PCB. Pin length: 33mm x 1mm dia. holes, which should be drilled 6mm from edge of PCB. Available in 2, 3, 4 and 12-way.
These connectors are intended as a simple and inexpensive method of making cable to printed circuit board connections. The pins are at standard 0.1 (2.54mm) pitch. These header plugs are designed primarily for accepting the matching sockets below allowing cables to be plugged onto circuit boards or circuit boards to be plugged together. The pins protrude 34mm from the base and require 1mm diameter holes for soldering to the PCB. The pins are 7.5mm long above the base and the header features a locking and polarising clip. Both plugs and sockets may be butted up end-to-end to form connectors with any number of ways from 2 upwards. Rated: 25A, 250Vac. Type Length (mm)
2-way 3.5
3-way 7
4-way 9.5
10-way 24.5
0.1" Series Socket Housing ( 0.1in Skt Terminals )
A series of sockets that will connect to the 0.1 series PCB plugs. To assemble, solder metal PCB terminals to the end of your wires and then insert them into the housing, where they lock in securely. This forms a polarised connector that will connect only one way round on the matching PCB header plug. Housings are available from 2 to 10 ways to match the plugs. The metal PCB terminals are sold separately in strips of 10 (Order Code YW25C).
0.1" Series Right-Angled Sockets ( PCB Skt 12-Way )
Housing with printed circuit type tin-plated phosphor bronze terminals pre-assembled with pins at right-angles to the housings for direct PCB mounting. Thus boards with straight 0.1 series plugs may be connected at right- angles and boards with right-angle plugs may be connected end to end. The housing has a clip which holds it against the edge of the PCB. Pin length: 33mm x 1mm dia. holes, which should be drilled 6mm from edge of PCB. Available in 2, 3, 4 and 12-way.
0.1" Series Socket Housing ( PCB Ltch Hsng 10-Way )
A series of sockets that will connect to the 0.1 series PCB plugs. To assemble, solder metal PCB terminals to the end of your wires and then insert them into the housing, where they lock in securely. This forms a polarised connector that will connect only one way round on the matching PCB header plug. Housings are available from 2 to 10 ways to match the plugs. The metal PCB terminals are sold separately in strips of 10 (Order Code YW25C).
These connectors are intended as a simple and inexpensive method of making cable to printed circuit board connections. The pins are at standard 0.1 (2.54mm) pitch. These header plugs are designed primarily for accepting the matching sockets below allowing cables to be plugged onto circuit boards or circuit boards to be plugged together. The pins protrude 34mm from the base and require 1mm diameter holes for soldering to the PCB. The pins are 7.5mm long above the base and the header features a locking and polarising clip. Both plugs and sockets may be butted up end-to-end to form connectors with any number of ways from 2 upwards. Rated: 25A, 250Vac. Type Length (mm)
2-way 3.5
3-way 7
4-way 9.5
10-way 24.5
A collection of a thousand
coloured cable ties in a handy portable canister. The kit comprises 100 each of 10 different coloured 100mm ties. Manufactured in nylon 66 to UL94V-2, temperature range -40C to 105C.
Length Width Max dia. Max
load
100mm 2.5mm 25mm 8kg
Plug this dongle into your PC & turn it into a Bluetooth enabled device
Download pictures from your Bluetooth™ mobile phone to your PC
100m range
Bluetooth™ v1.2 for improved features
Base diameter 10mm, height 14mm. Available for the following spindle diameters: 4mm (JZ45Y) and 3175mm (1/8in.) (JZ46A). Caps available in red and black.
Base diameter 10mm, height 14mm. Available for the following spindle diameters: 4mm (JZ45Y) and 3175mm (1/8in.) (JZ46A). Caps available in red and black.
Base diameter 10mm, height 14mm. Available for the following spindle diameters: 4mm (JZ45Y) and 3175mm (1/8in.) (JZ46A). Caps available in red and black.
Two 12Vdc sleeve bearing axial fans with plastic housings
and blades to UL94V-0
80mm Fan max airflow is 40 CFM ( 1130 Litres/minute)
60mm Fan max airflow is 18.7 CFM (528 Litres/minute) Specifications:
Code: RG02C RG03D
Operating voltage: 10.2-13.8Vdc
Rated voltage: 12Vdc
Rated current: 130mA 200mA
Rated I/P power: 1.56W 2.4W
Noise: 30dB 35dB
Insulation resistance: 10MΩ@500V
Operating temp: -10 to +70C
DC dielectric strength: 5mA 500V AC
Weight: 70g 100g
Size (mm): 60 x 60 x 25 80 x 80 x 25
Two 12Vdc sleeve bearing axial fans with plastic housings
and blades to UL94V-0
80mm Fan max airflow is 40 CFM ( 1130 Litres/minute)
60mm Fan max airflow is 18.7 CFM (528 Litres/minute) Specifications:
Code: RG02C RG03D
Operating voltage: 10.2-13.8Vdc
Rated voltage: 12Vdc
Rated current: 130mA 200mA
Rated I/P power: 1.56W 2.4W
Noise: 30dB 35dB
Insulation resistance: 10MΩ@500V
Operating temp: -10 to +70C
DC dielectric strength: 5mA 500V AC
Weight: 70g 100g
Size (mm): 60 x 60 x 25 80 x 80 x 25
A useful selection af
cable ties in a handy zip lock bag. Kit comprises 150 ties: 50 each of the 100mm, 203mm and 280mm ties with 10 pieces each in natural, black, blue, red and yellow. All cable ties are manufactured in nylon 66 to UL94V-2, temperature range -40C to 105C. Length Width Max dia. Max load
100mm 2.5mm 25mm 8kg
203mm 3.2mm 55mm 18kg
280mm 4.8mm 9.1mm 22kg
Base diameter 15mm, height 14mm. Available for the following spindle diameters: 6mm (JZ50E) and 6.35mm (1/4in.) (JZ47B). Caps available in red, green, and black.
Base diameter 15mm, height 14mm. Available for the following spindle diameters: 6mm (JZ50E) and 6.35mm (1/4in.) (JZ47B). Caps available in red, green, and black.
Base diameter 15mm, height 14mm. Available for the following spindle diameters: 6mm (JZ50E) and 6.35mm (1/4in.) (JZ47B). Caps available in red, green, and black.
Base diameter 15mm, height 14mm. Available for the following spindle diameters: 6mm (JZ50E) and 6.35mm (1/4in.) (JZ47B). Caps available in red, green, and black.
Base diameter 15mm, height 14mm. Available for the following spindle diameters: 6mm (JZ50E) and 6.35mm (&quarter;in.). Caps are available in red and black.
16A PCB-Mounting Terminal Blocks ( 2W 16A Vert 5mm )
·5mm pitch, 16A rated
·Rising clamp cable entry
·Interlocking facility for connecting multiple connectors Available in 2-way and 3-way versions that can be interlinked to make any number way. The 16A rating means these terminal blocks are able to carry any current from 0 to 16 amps. Specifications:
PCB hole size: 1.3mm
Pitch: 5mm
Max. cable size:
stranded: 2.5mm
solid: 4mm
Nominal voltage: 250V
Nominal current: 16A
16A PCB-Mounting Terminal Blocks ( 3W 16A Vert 5mm )
·5mm pitch, 16A rated
·Rising clamp cable entry
·Interlocking facility for connecting multiple connectors Available in 2-way and 3-way versions that can be interlinked to make any number way. The 16A rating means these terminal blocks are able to carry any current from 0 to 16 amps. Specifications:
PCB hole size: 1.3mm
Pitch: 5mm
Max. cable size:
stranded: 2.5mm
solid: 4mm
Nominal voltage: 250V
Nominal current: 16A
1Gb Cruzer Crossfire USB Flash Drive ( 1Gb Crossfire USB )
1Gb Performance Sandisk USB flash drive
Take your PC game data, music, video, and photos wherever you go and share your music and photos from your PC to Xbox 360
No drivers required, plug-n-play
Hi speed USB 2.0 for fast data transfer SanDisk Cruzer Crossfire USB flash drives maximize your world of entertainment!
Pin strips which are used in conjunction with pin jumpers to provide option pins on computers, disk drives and other electronic hardware. These pin strips provide an easy means of being able to select various firmware options. Strips may be shortened by cutting at V-notches so any required length may be formed. Available in single and double rows of 36.
Pin strips which are used in conjunction with pin jumpers to provide option pins on computers, disk drives and other electronic hardware. These pin strips provide an easy means of being able to select various firmware options. Strips may be shortened by cutting at V-notches so any required length may be formed. Available in single and double rows of 36.
Miniature jumpers for bridging option pins on computers, disk drives, etc. Miniature jumpers for bridging option pins on computers, disk drives and other electronic hardware. Used in conjunction with 2.54mm (0.1in.) pin strips, these jumpers provide an easy means of being able to select various firmware options. Two versions are available, with or without extraction handle. Sold in packs of 10.
Miniature jumpers for bridging option pins on computers, disk drives, etc. Miniature jumpers for bridging option pins on computers, disk drives and other electronic hardware. Used in conjunction with 2.54mm (0.1in.) pin strips, these jumpers provide an easy means of being able to select various firmware options. Two versions are available, with or without extraction handle. Sold in packs of 10.
A good quality edge connector primarily for use with double-sided pcbs. Moulded in glass-fibre reinforced polyester UL94-V0, the connector has gold-plated phosphor bronze contacts. Available in 2x31 way.
Base diameter 21mm, Height 17mm. Available for 6·35mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 635mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 6·35mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 635mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 6·35mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 635mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 6·35mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
Base diameter 21mm, Height 17mm. Available for 635mm (1/4in.) and 6mm diameter shafts. Caps available in black and red. Knob base is recessed to hide control fixing nut.
A 230Vac mains axial fan for cooling, extraction, intake, ventilation, etc. Available in two standard sizes: 80mm (3in.) and 120mm (4in.). The fans feature an impedance protected shaded-pole motor with a sintered iron sleeve bearing. The frame is diecast aluminium with a steel impeller, finished in black epoxy paint.
The 120mm unit has five blades and the 80mm has nine blades.
The 120mm fan has solder tag connections and a clear 2BA (M5) fixing hole for earth connection. The 80mm fan has 280mm leads (for connection inside equipment only) and a hole in the chassis (for self-tapper M4) for earth connection.
Plastic finger guards are available in 80mm (Order Code JU26D) and 120mm (JU27E).
Standard 80mm Fan max airflow is 28CFM (792 Litres/minute)
Standard 120mm Fan max airflow is 78CFM (2200 Litres/minute)
Specifications:
Type: 80mm 120mm
Power consumption: 13W 22W
Continuous life: 20,000 to 40,000 hours at 40C
Motor current: 85mA 140mA
Stall current: 105mA 180mA
Noise level: 33dBA 45dBA
Max. airflow: 28CFM 80CFM
Speed: 2700rpm 2650rpm
Overall size: 80 x 80 x 119 x 119 x
38mm 38mm
Fixing centres: 715 x 715 105 x 105
45mm clear 45mm clear
Operating temp: -10C to +60C
A 230Vac mains axial fan for cooling, extraction, intake, ventilation, etc. Available in two standard sizes: 80mm (3in.) and 120mm (4in.). The fans feature an impedance protected shaded-pole motor with a sintered iron sleeve bearing. The frame is diecast aluminium with a steel impeller, finished in black epoxy paint.
The 120mm unit has five blades and the 80mm has nine blades.
The 120mm fan has solder tag connections and a clear 2BA (M5) fixing hole for earth connection. The 80mm fan has 280mm leads (for connection inside equipment only) and a hole in the chassis (for self-tapper M4) for earth connection.
Plastic finger guards are available in 80mm (Order Code JU26D) and 120mm (JU27E).
Standard 80mm Fan max airflow is 28CFM (792 Litres/minute)
Standard 120mm Fan max airflow is 78CFM (2200 Litres/minute)
Specifications:
Type: 80mm 120mm
Power consumption: 13W 22W
Continuous life: 20,000 to 40,000 hours at 40C
Motor current: 85mA 140mA
Stall current: 105mA 180mA
Noise level: 33dBA 45dBA
Max. airflow: 28CFM 80CFM
Speed: 2700rpm 2650rpm
Overall size: 80 x 80 x 119 x 119 x
38mm 38mm
Fixing centres: 715 x 715 105 x 105
45mm clear 45mm clear
Operating temp: -10C to +60C
A novel plastic case designed
so that a 25-way D-connector will fit in each end. Small circuits may be built into the box which has a useful internal size of 38mm between connectors, 36mm wide and 11mm deep.The box snaps together with interlocking clips.
Connectors type YQ48C, YQ49D from our range will fit in this box.
2mm plug with solder-bucket termination and screw-on plastic body. Overall length 14mm, pin length 9mm and body diameter 5mm, available in red and black.
2mm plug with solder-bucket termination and screw-on plastic body. Overall length 14mm, pin length 9mm and body diameter 5mm, available in red and black.
30A Insulated Battery Clips ( Large Batt Clip Red )
Large, heavily-sprung clip for use with battery chargers etc. Overall length 74mm; maximum diameter of terminal that can be encompassed 15mm; maximum gap between teeth of jaws when fully opened 10mm. Current rating 30A with very thick PVC insulating cover available in red or black.
30A Insulated Battery Clips ( Large Batt Clip Blk )
Large, heavily-sprung clip for use with battery chargers etc. Overall length 74mm; maximum diameter of terminal that can be encompassed 15mm; maximum gap between teeth of jaws when fully opened 10mm. Current rating 30A with very thick PVC insulating cover available in red or black.
